276°
Posted 20 hours ago

PacTool SA90376 Gecko Gauge LP Siding Mounting Block - Compatible with 7/16-inch Siding : Everything Else – 7/16” Siding

£37.16£74.32Clearance
ZTS2023's avatar
Shared by
ZTS2023
Joined in 2023
82
63

About this deal

Size: Make sure you buy the right size clamp for your application. If the clamp is too large or too small it wont be able to secure the siding properly. It is absolutely critical to mark where your studs are when installing house wrap. You want to always hit a stud when nailing the siding. Mark where the studs are by finding one and using a level to mark a line from the top of it to the bottom of the area. Repeat this at every stud location.

Siding – most suppliers carry Hardiplank, but ask if they carry another brand that may be cheaper. I personally used Nichiboard and it worked out to be a 30% savings as opposed to Hardie plank. Cutting around windows and door frames is pretty straightforward. Use the tape measure to find out where the cut needs to be made, and use the framing square to accurately trace where the cuts need to be made on the corresponding piece of siding. Try to make these cuts as tight as possible. Although the painters will caulk the small gap between the end of the siding, and the corner trim, craftsmanship always wins and it will only help while striving for a water-tight finish. How to Install 4×8 Hardie Board Siding DIY Projects: Get rid of bulky spacer guides with these durable clamps; machined from industrial-grade components for years of use Other styles of fiber cement siding include shingles, vertical siding, 4×8 panels, trim, and soffit panels. How Much Does Fiber Cement Siding Cost? Metal Clamp: Easily attaches each Z clamp to the first course of flashing before placing the panel on the support plate simply nail as per manufacturer recommendationsYou’ll find that these boards are flimsier than they seem to be, so you don’t want them to span a distance larger than 16″ without hitting a stud. Step 5 – Install the Rest You want a snug fit on the siding. The tightening lever should make no less than a 45 degree angle with the upper half of the siding. Overtightening can cause the gauge to pull away from the wall. Tha... Siding Nails– These can vary, but the standard is a 2.5” siding nail. If you’re unsure of what nails you’ll need, ask someone in that department. A: Simply attach each Z clamp to the first course of flashing before placing the panel on the support plate – then nail as per manufacturer recommendations before continuing up the wall. Like any substantial project, you’re going to have times when you’re tired, you’ve been working all day, and looking at the area left to do is daunting. That’s Okay! After flipping my first house, this was probably one of the most important lessons I’ve learned.

Make sure that the clamps are both set to the same level of reveal that you desire. Most of the time homeowners want a 7.25”-7.5” reveal, so play around and find what you like. Hardie board is named after the James Hardie Brand, it’s arguably the most widely recognized brand of fiber cement siding. Other brands include: Start at the highest point you can, and pry the old siding off from the top down. Make sure to remove ALL nails. The last thing you want is to find out you missed a nail after setting a new hardie plank panel into place. Step 2 – Install House Wrap A: The patented friction cam mechanism allows this tool to fully support 16 foot lengths of LP Siding ensuring equal spacing between each board. A: The PacTool SA907 Adjustable Z-Clamp Panel Siding Installation Tool is machined from industrial grade components.Fiber Cement siding is a combination of cement, water, sand, and cellulose fibers. The combination of these compounds provides a strong, long-lasting option for a home’s exterior. Another benefit of fiber cement is the ability to hold paint. Due to its porous nature, the material soaks up paint when applied. Tests have shown that paint also withstands fade from UV rays on fiber cement siding better than it would on other siding materials. I know marking studs can be tedious, but if done improperly you risk hitting water and electrical lines when nailing in the siding. Step 3 – Install Trim For distances longer than the length of your siding (typically 12 feet) you’ll need to butt two pieces together at a stud. Some experts recommend leaving a ⅛” gap in between boards, but I don’t think this is necessary. This is good practice for real wood material due to its tendency to absorb moisture and expand. A quality fiber cement product will not swell enough to do any damage. I like to butt them as close as possible because a good painter can hide the seam with caulk. Material: Choose a material that is strong enough to hold up against wind, rain, snow, and other weather conditions. Metal is usually the strongest option, but plastic can work for lighter materials like vinyl or fiber cement. If you have someone helping you, have them hold the starting board while you ensure its level. Once you find the perfect spot, start nailing it to the house at the studs. Hit every stud you can.

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment